The OSHA standard that provides the guidelines for a lockout/tagout procedure is 29 CFR 1910.147, titled "The Control of Hazardous Energy (Lockout/Tagout)." It covers servicing and maintenance of machines where unexpected energization, startup, or release of stored energy could injure workers. The standard applies to general industry and took effect in 1989.

The energy-isolation mechanism behind 1910.147

Lockout/tagout works by creating a physical barrier between a hazard and the worker. The barrier is a lock, and the tag is a warning that travels with it. OSHA requires the lock to be singular in purpose: a device that holds an energy-isolating switch in the safe position and that only the person who applied it can remove.

The logic matters more than the hardware. A machine can store energy in several forms at once. Electricity is the obvious one, but the standard also names pneumatic pressure, hydraulic pressure, coiled springs, gravity, steam, and thermal energy. Releasing any one of these while a worker is inside the equipment can cause injury or death. Isolation must therefore address every energy source, not just the electrical feed.

OSHA splits the requirement into two distinct procedures. The energy control procedure is the written program that describes how a specific machine is shut down, isolated, and verified. The lockout/tagout procedure is the step-by-step execution of that program at the point of work. The standard requires the employer to develop, document, and implement both, and to inspect them at least annually.

The verification step is where thin explainers usually stop. After isolation, a worker must attempt to start the equipment or otherwise confirm that no energy remains. That test is called tryout, and it is the single control that proves the lock actually worked. A lock on the wrong valve isolates nothing.

Authorized employees apply locks. Affected employees operate or work near the equipment, and other employees may need to be trained only to recognize the tags. The distinction matters because training obligations and removal authority differ by role.

Quantified scope of lockout/tagout in US workplaces

Lockout/tagout was written against a measurable hazard base. OSHA estimated at the rule's adoption that the standard would prevent roughly 120 fatalities and 50,000 injuries annually among workers exposed to hazardous energy during servicing and maintenance. Those figures came from rulemaking analysis, not from a controlled trial, so treat them as estimates of scale.

The standard reaches a large population. OSHA has estimated that about 3 million workers across general industry service equipment covered by 1910.147, and that roughly 39 million workers are exposed to lockout situations in some form when construction and other sectors are counted. Compliance costs were estimated in the rulemaking at roughly USD 30 per employee per year for training and hardware, a figure now decades old.

Annual inspection is a hard calendar requirement, not a suggestion. The periodic inspection of the energy control procedure must occur at least once every 12 months, and it must be performed by an authorized employee other than the one using the procedure. That independence requirement is easy to miss.

Recordkeeping is lighter than many assume. OSHA does not require a specific logbook format for lockout/tagout, but the employer must be able to document that the written procedure exists and that the annual inspection occurred. In practice, most programs keep a procedure binder and an inspection spreadsheet for exactly this reason.

Where lockout/tagout breaks: edge cases the standard anticipates

The standard contains provisions for situations that defeat a simple lock-and-tag flow. Group lockout is one. When several crews work on the same system, each authorized employee must apply a personal lock to a group lockout device so no single person's departure re-energizes the equipment. OSHA describes this in 1910.147(f)(3), and getting it wrong is a common citation.

Shift changes are another edge case. When a lockout crosses shifts, the standard expects a orderly transfer of lockout responsibility, with the outgoing authorized employee removing a lock only after the incoming worker applies their own. Removing a lock to "hand off" without a new lock in place defeats the barrier.

Tags alone are not locks. A tagout device is a warning, not a physical restraint, and 1910.147(c)(3) allows tagout only when the employer can demonstrate that a lockout device cannot be used, or when tagout provides equivalent protection. Even then, the employer must show that the tagout system is at least as effective, which is a high bar. Where a lock can be applied, it must be.

A counterintuitive professional caveat: the standard does not cover every worker on site. It applies to servicing and maintenance, not to normal production operations. If a machine must be energized or partially energized during servicing because the work cannot otherwise be performed, the employer must use alternative protective measures under 1910.147(a)(2)(ii) and specific control measures under 1910.333(b) for electrical work. The exemption is narrow, and it shifts the burden onto documented alternative controls.

Cord-and-plug equipment gets its own rule. When a machine is cord-and-plug connected and unplugging it removes all energy, the plug itself can serve as the isolating device, provided the plug stays under the exclusive control of the worker. That does not license unplugging a 480-volt hardwired panel.

Red flag: a tag on a valve with no lock when a lock is feasible. Red flag: annual inspection signed by the same employee who performs the procedure. Red flag: group lockout with a single shared lock and no individual locks. Red flag: a written procedure that covers shutdown but not stored-energy release. Red flag: removal of a lock without documented verification that the work is complete.

Comparison: 1910.147 versus the other lockout authorities

Lockout requirements live in more than one place, and operators frequently confuse them. The table below maps the main authorities.

Standard Scope Key lockout requirement
29 CFR 1910.147 General industry servicing and maintenance Written energy control program, lockout/tagout, annual inspection
29 CFR 1910.333(b) Electrical work practices for qualified persons Lockout and tagging of circuits, plus verification of de-energization
29 CFR 1926.417 Construction Locking and tagging of circuits during construction work
29 CFR 1910.269 Electric power generation, transmission, distribution Lockout/tagout for power-line work, with specific clearance procedures
29 CFR 1910.147(c)(3) Tagout allowance within 1910.147 Tagout only when lockout is infeasible or equally effective
NFPA 70E Consensus electrical safety standard Addresses lockout as part of electrical safety program, not law itself

The practical takeaway: 1910.147 is the general-industry baseline, but electrical work often triggers 1910.333(b) as well, and construction sites follow 1926.417. A compliant program cites 1910.147 and then checks which of the other standards apply to the specific task.

Timeline: from energy present to energy restored

A lockout/tagout procedure runs on a defined sequence. The table below shows the stages and what must be documented at each.

Stage Action Verification point
1. Notify Notify affected employees that servicing is starting Notification logged or communicated
2. Shut down Use the normal stopping procedure, not the disconnect Equipment fully stopped
3. Isolate Open the energy-isolating device for every energy source Device in safe position
4. Lock and tag Apply lock and tag to each isolating device Lock is personal and exclusive
5. Release stored energy Bleed pressure, discharge capacitors, block gravity loads Stored energy confirmed gone
6. Verify Try to start the equipment or test for zero energy Tryout confirms isolation
7. Work Perform the servicing Lock stays in place
8. Restore Remove locks only by the applier, then re-energize Sequence confirmed and recorded

Two details deserve emphasis. Stage 3 must cover each energy source separately, so a machine with an electrical feed and an air line needs two isolations. Stage 8 permits lock removal only by the employee who applied the lock, with narrow exceptions for the employer's removal procedure when the applier is unavailable. That removal procedure must be written and documented, and it is one of the most scrutinized parts of any program.

Misconceptions that survive repeated audits

The most durable misconception is that lockout/tagout equals a padlock. A lock without a written procedure is an incomplete program. OSHA can cite an employer for missing documentation even when the lock is applied correctly, because 1910.147(c)(4) requires the procedure to be documented, except where the employer can show the machine has a single energy source that is fully de-energized by one isolating device and that isolation is verified.

A second misconception is that training is a one-time event. The standard requires training at the time of initial assignment and whenever a change in job assignment, machine, or procedure creates new exposure. Retraining is also required when periodic inspections reveal deviations or inadequacies. That makes training a maintenance activity, not an onboarding checkbox.

A third is that tagout is a cheaper lockout. The standard treats tagout as a fallback that must be justified. When tagout is used, the employer must provide additional training and demonstrate that the tagout device and warning are at least as effective as a lock would have been.

The fourth is that the procedure ends when the work ends. Restoration of energy is part of the procedure, and the sequence of removing locks and re-energizing must be documented and verified. Getting re-energization wrong can injure a worker who assumes the machine is still isolated.

A fifth misconception concerns contractors. When a contractor performs servicing, the host employer and the contractor must coordinate lockout procedures. OSHA expects the on-site employer to inform contractors of the lockout program and to ensure that contractor personnel follow it. That coordination is a documented obligation, not a courtesy.

Practical actions to build a compliant lockout/tagout program

Start with an inventory. List every machine that requires servicing and every energy source each machine contains. For each, write a procedure that covers shutdown, isolation, stored-energy release, and verification. That inventory is the backbone of the program, and OSHA inspectors commonly ask for it first.

Assign locks to individual authorized employees and maintain a lock-log or key-control record. Establish a written procedure for lock removal when the applier is unavailable, and require a manager or designated representative to document the exception. Review that exception each time it is used.

Set the calendar. Schedule the annual periodic inspection per procedure and assign an authorized employee who does not use that procedure. Inspect at least once every 12 months, and record the inspector, the date, the procedure reviewed, and any deficiencies found. Correct deficiencies and document the correction.

Train by role. Authorized employees need training on the specific procedures and devices they use. Affected employees need training on the purpose and limits of lockout and on the prohibition against removing locks. Refresher training follows procedure changes and inspection findings.

Verify hardware. Confirm that locks are durable, standardized, and identifiable to the individual. Confirm that tags are legible, standardized, and state the warning and the identity of the applier. Confirm that isolating devices can be locked in the safe position.

Document everything. Keep the written procedures, training records, annual inspection records, and lock-removal exceptions in one accessible file. That file is the program's evidence trail, and it is what turns a lock on a valve into a defensible compliance position.

Limits of the standard and what it does not cover

1910.147 does not regulate every activity. It applies to servicing and maintenance, and it excludes normal production operations, cord-and-plug equipment under exclusive worker control (where unplugging suffices), and certain work covered by more specific standards. Construction, maritime, and agricultural operations are addressed by their own standards, not by 1910.147.

The standard also does not specify hardware models, lock colors, or a single acceptable tag format. It sets performance requirements, so compliance is judged on whether the isolation actually protects the worker, not on whether a particular padlock was purchased. That flexibility is useful, but it means employers cannot rely on buying the right lock alone.

OSHA does not prescribe a universal written procedure template. It requires the procedure to identify the machine, the energy sources, the isolation method, and the verification method. A procedure that omits stored-energy release is incomplete even if it names every disconnect.

The numbers in this article describe OSHA's rulemaking estimates and the standard's stated thresholds, not measured outcomes in a specific facility. Site-level injury and citation data vary by industry and program quality. Verify current requirements against the text of 29 CFR 1910.147 and any applicable state plan, since some states operate their own occupational safety programs with additional requirements.

This article is general educational information about workplace safety regulation, not a legal opinion or a compliance certification. It does not promise any outcome and does not replace a site-specific evaluation. Consult a qualified safety professional or your local OSHA area office, or legal counsel for jurisdictional questions, before relying on this material for compliance decisions.